close
    what causes water to come out of my tub spout and shower head at the same time

    +1  Views: 836 Answers: 2 Posted: 12 years ago
    Tags: plumbing

    2 Answers

    Is this a euphimism?

    The diverter valve on the faauct is worn out.  You should replace the faucet spout, and both seats, and you may as well buy new handles at the same time.  The seats cost about $10.00 a piece.Faucet about $15.00, handles about $15.00, labor-A plumber will charge about !00.0 bucks,(approx) but you can do it youself.


    A. Turn off the water.


    B.  Remove caps on handles with a thin flat head screwdriver.


    C.  Unscrew the handles with a phillips screwdriver.


    D. Wiggle the handles until they come off.


    E. Remvove the back plate, which exposes the seats use a wrench to remove the brass lock ring.


    F Seats are plastic on relatively modern tub/shower faacets.


    G. wiggle the seats out, and take to Ace for a match.


    H.  Obtain with the seats a small rubber gasket kit-grease the rubber gasket with plumbers lube, and insert it in the off-center hole where the seats go- You have to make it fit in there with your finger.  Be sure it is in there correct.


    I.  Install the new seats-Don't tighten the brass lock ring to tight- Just tight enough so they don't leak from the handles.


    J. Install the new handles just like you removed the old ones- replace the caps.


    K.  Now unscrew the faucet spout-don't worry about damaging it with a pipe wrench if need be.Sometimes they get stuck with calcimation.  Lefty Luoosey-Righty Tighty.,But if the dog-gone thing is from the relatively old days it may be soldered- In that case you'll have to call a plumber.  Check it - if it gives slightly, or its relatively modern then you know it screws on.


    L.  Wrap the water supply pipe (nipple) with white plumbers tape-2 wraps completely around, and screw on the new faucet all the way to the tile- It can be hand tightened, just make sure its good and tight and straight


    M.  Caulk around the edges-Tube caulk sells for about $3 , the kind you don't need a caulk gun for-Cut the tube flat instead of at an angle, and smear it in the space with your fingers-use a damp sponge for clean up- and dry with a paper towel-and don't use it, at least overnite.


    The above info is for info only, and I the writer accepts no responsiblity for the outcome, but I can tell that http://www.mcbikergear.com has a philosophy that possibly could help pay the plumber..


     


     



    Top contributors in Uncategorized category

     
    ROMOS
    Answers: 18061 / Questions: 154
    Karma: 1101K
     
    Colleen
    Answers: 47269 / Questions: 115
    Karma: 953K
     
    country bumpkin
    Answers: 11322 / Questions: 160
    Karma: 838K
     
    Benthere
    Answers: 2392 / Questions: 30
    Karma: 760K
    > Top contributors chart

    Unanswered Questions

    Doksov Stream
    Answers: 0 Views: 1 Rating: 0
    bxtayhaiduong
    Answers: 0 Views: 3 Rating: 0
    pkwindev
    Answers: 0 Views: 8 Rating: 0
    bongdaluukcom
    Answers: 0 Views: 7 Rating: 0
    bongdaluukcom
    Answers: 0 Views: 4 Rating: 0
    i9bet01live
    Answers: 0 Views: 5 Rating: 0
    Yarkam Live
    Answers: 0 Views: 11 Rating: 0
    Cuevana2 kim
    Answers: 0 Views: 13 Rating: 0
    > More questions...
    466473
    questions
    722247
    answers
    785405
    users